manualshive.com logo in svg

IHI IC50, Руководство по эксплуатации

IHI IC50 - устройство высокой производительности для эффективной работы. Скачайте бесплатное руководство по эксплуатации с нашего сайта для получения подробных инструкций о работе с устройством. Загрузите его сейчас с manualshive.com и начните использовать ваш продукт с максимальной эффективностью.

Поделиться
Скачать
background image

MAINTENANCE 

IC50 ENG 

4-14 

Replace the hydraulic oil and clean the strainer 

 

  

WARNING 

•

  Be sure to set the safety bars under the body 

before starting works with the body raised. 

•

  Oil is hot immediately after operation.  You may 

get burnt if you touch oil.  Start work after oil 
has cooled down. 

 
1.  Place the machine on a flat and rigid ground and bring 

it into the posture for changing hydraulic oil.  Stop the 
engine. 

2.  Open the cover (1).  Discharge hydraulic oil through 

the filler port (2) into an empty drum with an oil pump. 

3.  Put the container under the drain plug (3) at the bottom 

of the hydraulic oil tank, and remove the drain plug to 
discharge residual oil. 
Tighten the drain plug after discharging oil. 

4.  Remove the cover (4), (5).  Disconnect the hose from 

the tube (6).  Remove the bolt (7) and take out the 
strainer (8). 

5.  Clean the strainer to remove dust and foreign matters. 
6.  Attach the strainer in the reverse order to step 4. 
7.  Fill the tank with hydraulic oil through the filler port up 

to the L level of the level gauge (9).  Tighten the filler 
port plug. 

8.  Store the safety bars and start the engine.  Keep the 

engine running with no load for approximately 5 
minutes.  Travel the machine and move the dump 
cylinder slowly several times.  Bring the machine into 
the posture for checking the hydraulic oil level.  Stop 
the engine. 

9.  Make sure that the hydraulic oil level is within the 

proper range.  Refill hydraulic oil if insufficient. 

 

Posture for replacing the 

hydraulic oil  

Содержание IC50









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC50

SANY SY215C LC Operation And Maintenance Manual preview
SY215C LC
Бренд: SANY Страницы: 272
IMC IMPACTOR IP700 Installation, Operating And Maintenance Manual preview
IMPACTOR IP700
Бренд: IMC Страницы: 13
New Holland LS120 Repair Manual preview
LS120
Бренд: New Holland Страницы: 41

Бренды по названию

Популярные бренды

Загрузить еще бренды