IHI IC50 Скачать руководство пользователя страница 24

Страница: 24 / 104

SAFETY

IC50 ENG

1-14

7. Warning!

Read manual before
operation, maintenance,
disassembly, assembly
and transportation.
(D405 359 00)

8. Sign indicates a burn

hazard from spurting
hot water or oil if
radiator or hydraulic
tank is uncapped
while hot.
Allow radiator or
hydraulic tank to cool
before removing cap.
(D405 360 00)

9. Sign indicates a burn

hazard from touching
heated parts, such as
engine, motor, or muffler
during or right after
operation. Never touch
when hot.

(D405 361 00)

10. Sign indicates an

electrical hazard from
handling the cable.
Read manual for safe
and proper handling.
(D405 363 00)

11. Sign indicates an

electrocution hazard if
machine is brought too
near electric power lines.
Keep a safe distance
from electric power lines.
(D405 364 00)

12. Sign indicates a

hazard of falling.
Do not stand on this
place.
(D405 365 00)

13. Sign indicates a hazard

of rotating parts, such as
belt.
Turn off before
inspection and
maintenance.
(D405 366 00)

14. Sign indicates a

hazard of falling out
when machine goes
over an obstacle.
Read manual and
follow instructions for
safe and proper
operation.
(D405 368 00)

Содержание IC50









































































































Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды

IHI IC50, Руководство по эксплуатации

Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды