IHI IC50 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 104

background image

MAINTENANCE

IC50 ENG

4-22

Check the fan belt

WARNING

To help avoid being injury, check and adjust the fan
belt tension with engine stopped.
Parts are hot immediately after the engine stops.
You may get burnt.

Check

1. Push a point in the middle of the idle pulley (1) and

alternator pulley (2) at approximately 98 N (10 kgf).
The belt tension is proper if the belt slacks by
approximately 6 to 8 mm.

2. Replace the belt if the adjustment margin of the belt is

lost or the belt has flaws or cracks.

Adjustment

1.  Loosen the alternator fixing bolt (3) and lock nut (4).

2.  Adjust the belt tension with the adjust bolt (5).

3.  Tighten the fixing bolt and lock nut firmly after

adjustment.

4. Keep the engine idling for 5 minutes and check the belt

tension.

«
...
80
81
82
83
84
...
»

Содержание IC50









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC50

Бренд: New Holland Страницы: 51

Бренд: Wacker Neuson Страницы: 252

Бренд: Wacker Neuson Страницы: 228

Бренд: Wacker Neuson Страницы: 248

Бренд: Whirlpool Страницы: 8

Бренд: jcb Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды