IHI IC50 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 104

background image

MAINTENANCE

IC50 ENG

4-27

Fuel system air bleeding

If air enters the fuel system, it hinders the engine from
starting and cause engine troubles.
Be sure to bleed the air of fuel system, when the fuel tank
is emptied, water is discharged from fuel, or the filter
element is replaced.

1. Set the engine key switch to the ON position to activate

the electromagnetic fuel pump.

2. Loosen the air bleeder plug (1) of the main fuel filter.

Move the priming pump (2) (20 times or more) until fuel
comes out.

3. Tighten the air bleeder plug. Move the priming pump

(10 times or more) until the fuel filter is filled with fuel.

4. Wait for approximately 1 minute. Loosen the air

bleeder valve to bleed the air of fuel system.

5. Repeat steps 2 to 4 until no air is discharged from the

air bleeder valve. (Three times at least)

6. Tighten the air bleeder plug firmly. Wipe off fuel

around.

7. Start the engine at the idling speed.

If the engine does not start, retry operation from step 3.

8. Keep the engine idling for 5 seconds.

9. Increase the engine speed gradually and keep the

maximum speed for 3 minutes.

10. Repeat steps 8 and 9 several times.

WARNING

Check if no fuel leaks from the fuel system.
Leaked fuel may cause a fire.

«
...
85
86
87
88
89
...
»

Содержание IC50









































































































Отзывы:

Нет отзывов

Похожие инструкции для IC50

Бренд: Wacker Neuson Страницы: 256

Бренд: Kubota Страницы: 182

Бренд: Takeuchi Страницы: 851

Бренд: jcb Страницы: 242

Бренд: jcb Страницы: 51

Бренд: RAMROD Страницы: 34

Бренд: Woods Страницы: 60

Бренд: Simar Страницы: 41

PC600-8 BACKHOE

Бренд: Komatsu Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды