IHI IC50 Скачать руководство пользователя страница 37

Страница: 37 / 104

CONTROLS

IC50 ENG

2-9

Operator seat

Sit on the seat and adjust it to allow free lever operations.

•

Adjusting tilt

Move the seat back while pulling the lever (1) to adjust
the angle of the seat back.

•

Adjusting the back-and-forth position

Move the seat forward or backward while pulling the
lever (2) to adjust the back-and-forth position.

•

Adjusting suspension

Raise the lever (3) and turn it to adjust suspension.
The appropriate body weight is displayed on the
display (4).

CAUTION

•

Do not adjust the seat while driving. Sudden

seat movement can cause operating errors or
unforeseen accidents.

•

Shake the seat back and forth lightly and check

if the seat is fixed firmly after adjusting it. If the
seat is not fixed, it may move suddenly and
cause unforeseen accidents.

Seat belt

1. Adjust the seat belt length according to your body size.
2. Confirm that the seat belt is not twisted and put the

plate (5) into the buckle (6) securely.

3. Slightly pull the belt and confirm the belt is locked.
4. Press the button (7) of the buckle to unfasten seat belt.

CAUTION

•

ALWAYS fasten the seat belt while operating

the machine.

•

ALWAYS check the condition of the seat belt

and mounting hardware before operating the
machine.
Replace the seat belt at least once every three
years, regardless of appearance.

Содержание IC50









































































































Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды

IHI IC50, Руководство по эксплуатации

Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды