IHI IC50 Скачать руководство пользователя страница 92

Страница: 92 / 104

MAINTENANCE

IC50 ENG

4-32

Check the battery

Refilling battery liquid

WARNING

•

The battery produces inflammable hydrogen

gas. It ignites or explodes if fire is nearby.
Never bring fire close to the battery or strike a
spark near it.

•

Never place any tool, metallic object or

inflammable matter on or near the battery.
The battery may possibly ignite and explode if it
short-circuits.

•

The battery liquid (diluted sulfuric acid) may

cause loss of eyesight or burning. If it is put
into the eyes or on the skin or clothes, wash
with much water immediately and consult a
doctor.

•

Be sure to put on protective goggles when

handing the battery.

Check the liquid level. Refill the battery with refill liquid up
to UPPER LEVEL, if it has lowered down to LOWER
LEVEL.

Cleaning the battery terminals

CAUTION

•

Be sure to keep the engine stopping during

work.

•

Be careful during work not to short-circuit the

positive and negative terminals of the battery
with a tool, etc.

•

Disconnect the battery cable from the negative

terminal first. Connect it to the negative
terminal last.

•

Tighten the terminals firmly.

1. Clean the terminals if they are dirty or corroded. (Pour

warm water onto the terminals and wipe them if they
are corroded and white powder sticks on them.)

2. Detach the terminals and polish them with a wire brush

or sandpaper if they are corroded remarkably.

3. Apply grease, etc. thinly to the terminals after cleaning

and tightening.

UPPER LEVEL

LOWER LEVEL

Содержание IC50









































































































Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды

IHI IC50, Руководство по эксплуатации

Результаты поиска

Содержание IC50

Отзывы:

Похожие инструкции для IC50

Бренды по названию

Популярные бренды