IEMCA BOSS 338 HD Скачать руководство пользователя страница 97

Страница: 97 / 214

5 - ADJUSTMENTS AND SETUP

Boss 338HD - 552HD

5 - Pag. 5 / 5

5.3.1 Guide channels, half bushes, bar pusher and collet - Replacement

• When the magazine is empty (no bars), set the

bar feeder to manual mode.

• Open the upper guard.

• Use the keyboard to move the bar pusher

forwards beyond the area of the bar
removal/loading clamp unit.

• (The bar pusher can be moved in manual mode

by means of the keyboard with the guard open
and the guide channels closed).

• Close the upper guard.

• On the keyboard, press the blue buttons and

the guide channel opening button
simultaneously to open the bar feeder guide
channels.

• Open the upper guard.

• Remove the feeding brushless motor guard to

fit the crank.

• Use the crank to bring the bar pusher to its

backwards limit stop and then remove it from
its seat. Bar pushers in the

=42

51 range

must be removed from the bar magazine.

Содержание BOSS 338 HD























































































































































































































Результаты поиска

Содержание BOSS 338 HD

Отзывы:

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию, Страница: 97 / 214

Результаты поиска

Содержание BOSS 338 HD

Отзывы: