manualshive.com logo in svg

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию, Страница: 12 / 214

Поделиться
Скачать
IEMCA BOSS 338 HD Скачать руководство пользователя страница 12

 

EN 

1   -   GENERAL INFORMATION 

Boss 338HD - 552HD

 

 
 

1 - Pag. 2 / 2 

 

 

 

  The operations described in the sections that are preceded by this symbol must be 

performed by qualified and skilled personnel with specific abilities and precise technical 
competence only. 

 

Any other operation can be performed either by qualified personnel and/or by 
professional bar feeder operators. 

 
 

  Before carrying out any operation on the bar feeder, it is of the utmost 

importance to read this manual carefully. 

 

 

1.1 WARRANTY 

CONDITIONS 

The applicable warranty period is subordinated to a correct assembly and coupling of the bar 
feeder to the lathe. In particular, prior to the first start-up, accurately make sure that the bar 
feeder is correctly aligned with the lathe and fixed with the expansion plugs as shown in 
chapter 4. 
The product warranty is valid only if the bar feeder is installed by an authorized technician with 
Original Installation Certificate. 
Please ask the technician who will make the installation to show the certificate, in order to 
ascertain the quality of the technical operations being carried out. 
The warranty shall begin from the date on the “Installation Certificate” duly filled in and signed. 
The document must be sent by mail to: 

TECHNICAL SERVICE DEPARTMENT 
IEMCA division of IGMI spa 
48018 Faenza (Ra) ITALY - Via Granarolo, 167 

Содержание BOSS 338 HD























































































































































































































Отзывы:

Нет отзывов