IEMCA BOSS 338 HD Скачать руководство пользователя страница 5

Страница: 5 / 214

INDEX

GENERAL INFORMATION Boss 338HD - 552HD ............................................................. 1

1.1 WARRANTY

CONDITIONS

...................................................................................................

1.2

PURPOSE OF THE MANUAL ............................................................................................... 3

1.3

MANUFACTURER AND BAR FEEDER IDENTIFICATION .................................................. 4

1.4 ASSISTANCE

REQUEST ...................................................................................................... 4

1.5 ATTACHMENT

LIST

............................................................................................................. 4

TECHNICAL INFORMATION Boss 338HD - 552HD .......................................................... 1

2.1

BAR FEEDER GENERAL DESCRIPTION ............................................................................ 2

2.2 OPERATING CYCLE ............................................................................................................. 4

2.3 SAFETY

DEVICES

................................................................................................................ 7

2.4

SAFETY PLATES - LOCATION AND DESCRIPTION .......................................................... 9

2.5 VERSION

DESCRIPTION

...................................................................................................

2.6 TECHNICAL

DATA

............................................................................................................. 11

2.6.1 Noise

levels

........................................................................................................................ 23

2.7

ACCESSORIES - FOREWORD ........................................................................................... 24

2.7.1

Bush holder device - Description ..................................................................................... 24

2.7.2

Axial displacement device - Description ......................................................................... 25

2.8

DEVICE FOR SLIDING HEADSTOCK LATHES - FOREWORD ........................................ 26

2.8.1

Bar/headstock synchronization device - Description ..................................................... 26

2.8.2

Telescopic front nose - Description ................................................................................. 27

2.9

DEVICES FOR CAM LATHES - FOREWORD .................................................................... 28

2.9.1

Headstock return device - Description ............................................................................ 28

2.9.2

Cam box - Description ....................................................................................................... 28

2.9.3

SAFETY PLATES - LOCATION AND DESCRIPTION ........................................................ 29

SAFETY - GENERAL INFORMATION Boss 338HD - 552HD ............................................ 1

3.1 GENERAL

SAFETY REGULATIONS ................................................................................... 2

3.2

HANDLING AND INSTALLATION - Safety .......................................................................... 3

3.3

ADJUSTMENTS AND SETUP - Safety ................................................................................. 3

3.4

USE AND OPERATION - Safety ........................................................................................... 4

3.5

BAR FEEDER MAINTENANCE - Safety .............................................................................. 5

3.6

EC DECLARATION OF CONFORMITY ................................................................................ 6

3.7

General Description of Supply ............................................................................................ 7

Содержание BOSS 338 HD























































































































































































































Результаты поиска

Содержание BOSS 338 HD

Отзывы:

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию, Страница: 5 / 214

Результаты поиска

Содержание BOSS 338 HD

Отзывы: