manualshive.com logo in svg

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию, Страница: 142 / 214

Поделиться
Скачать
IEMCA BOSS 338 HD Скачать руководство пользователя страница 142

 

EN 

6   -   USE AND OPERATION 

Boss 338HD - 552HD

 

 
 

6 - Pag. 22 / 22 

 

6.7 

AUTOMATIC CYCLE START AFTER MANUAL CYCLE OPERATIONS 

•  If the bar pusher has been moved while power supply was disconnected, the "BAR FEEDER 

ZERO SETTING" should be performed as follows: 

 

press the start buttons and 

 if the upper guide channels are not closed, the bar feeder 

will not perform the "BAR FEEDER ZERO SETTING"; messages will be displayed about the 
operations to carry out to bring the upper guide channels to the required position. 

 
After carrying out the required operations: 
 

•  Press the start buttons and 

. 

•  Check that the bar is in the required position in the lathe collet and that the collet is closed. 

• Press 

 to select the automatic function; the bar feeder will wait for an "OPEN COLLET" 

signal from the lathe. 

 
 

6.8 

AUTOMATIC CYCLE START - RESUMING WORK AFTER POWER-OFF 

IF THE BAR PUSHER HAS BEEN MOVED WHILE POWER WAS DISCONNECTED 

 

•  Power on the lathe. 
•  Turn the main switch to position I (ON). 

• Press 

 to select the manual mode. 

•  Press the start buttons and 

 to perform the "BAR FEEDER ZERO SETTING". 

•  Move the bar in the lathe collet to the required position and make sure that the collet is 

closed. 

• Press 

. 

 

IF THE BAR PUSHER HAS NOT BEEN MOVED WHILE POWER WAS DISCONNECTED 

 

•  Power on the lathe. 
•  Turn the main switch to position I (ON). 
•  Press [pupa_boss _avvio] to start the bar feeder 
•  Make sure that the lathe collet is closed. 

• Press 

. 

 

Содержание BOSS 338 HD























































































































































































































Отзывы:

Нет отзывов