IEMCA BOSS 338 HD Скачать руководство пользователя страница 125

Страница: 125 / 214

6 - USE AND OPERATION

Boss 338HD - 552HD

6 - Pag. 5 / 5

6.2

KEYBOARD CONTROL DESCRIPTION

1 Stops the bar feeder: for restart, manually

release the button.

2 Start buttons: opposite buttons enabling the

keys for some functions. Press both buttons and
simultaneously the button corresponding to the
desired function.

3 Selects the automatic mode.
4 Selects the manual mode.
5 Multifunction

- Allows scrolling the page upwards.

- Moves the selection cursor upwards.

- Increases by one the value set in the date

and time programming mode.

6 Multifunction

- Selects the previous parameter.

- Moves the selection cursor leftwards.

7 It resets the "BAR FEEDER ZERO SETTING" of

the carriage.

Hold down both start buttons and then the
key; release both buttons and the key when
the carriage starts moving towards the "BAR
FEEDER ZERO SETTING" position.

WARNING - CAUTION:

List of causes that require to carry out

the 0-Axis in manual mode.

Carrying out the manual 0-Axis

periodically is recommended.

If the bar pusher axis is moved by means

of the crank with the bar feeder powered

off (no power supply).

If the feeding chain is tightened (by means of the mechanical chain tightener,

see Operation and Maintenance Manual, "Feeding chain - Adjustment").

8 Lifts and lowers the bar selectors (LED on when selector switches are at their "down"

position).

9 Selects the bar pusher guide channels tooling function:

- Press both opposite start buttons and then the key; press and hold the keys until the

procedure is completed.

10 Multifunction

- Allows scrolling the page downwards.

- Moves the selection cursor downwards.

- Decreases by one the value set in the date and time programming mode.

11 Selects the semiautomatic function.

Press the button to select a mode and press again to deselect it.

Содержание BOSS 338 HD























































































































































































































Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды