IEMCA BOSS 338 HD Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 214

background image

EN

6 - USE AND OPERATION

Boss 338HD - 552HD

6 - Pag. 20 / 20

6.5.5 Cycle performing mode in the STEP BY STEP function

Foreword

This mode may be used for many reasons, as for instance:
•  to check a complete bar change cycle;
•  to check the bar feeder mechanics;
•  to load a single bar so as to check the facing;
• etc.

Procedure

•

check that the bar feeder is in the closed guide channel condition.

• press and

to select the semiautomatic function;

• press and the bar feeder performs the first step;

• press and the bar feeder performs the second step, and so on.

6.6

BAR FEEDER STOP

BAR FEEDER EMERGENCY STOP

WARNING - CAUTION:

if the emergency stop is activated whilst the lathe is working, before restarting

the machining cycle, check that no dangerous conditions arose due to the

sudden stop.

Example: if the tool was removing chips, before restarting the lathe, distance

the tool from the piece.

• To stop the bar feeder in emergency, press one of the emergency buttons of the bar feeder

or lathe.

BAR FEEDER STOP AT THE WORKING CYCLE END

WARNING - CAUTION:

when stopping the machine normally, do not use the emergency buttons.

• Complete the operations in your working schedule.

• Stop the bar feeder by pressing

.

• Stop the lathe.

«
...
138
139
140
141
142
...
»

Содержание BOSS 338 HD























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOSS 338 HD

Бренд: ACS Страницы: 56

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Gainsborough Страницы: 2

Бренд: Gainsborough Страницы: 2

Бренд: Gait up Страницы: 12

Бренд: Gait up Страницы: 6

Бренд: Gaiam Страницы: 2

Бренд: LA Audio Страницы: 9

Бренд: V-TAC Страницы: 13

Бренд: Y.I.C. TECHNOLOGIES Страницы: 6

Бренд: IBC Страницы: 4

Бренд: ProLights Страницы: 28

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренд: ABB Страницы: 136

Бренд: ABB Страницы: 108

Бренд: Beckman Coulter Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды