IEMCA BOSS 338 HD Скачать руководство пользователя страница 68

Страница: 68 / 214

4 - HANDLING AND INSTALLATION

Boss 338HD - 552HD

4 - Pag. 8 / 8

4.4.3 Preliminary

positioning

• Place the bar feeder behind the lathe,

considering the fixed and moving
dimensions of both machines. Coupling
distance "B" should not exceed bar pusher
max. extension "A".

1  Fixed headstock or sliding rest lathe
2  Sliding headstock CNC lathe
3  Sliding headstock cam lathe

INFORMATION:

it is not always necessary to drive

the bar pusher all the way out. In

fixed headstock lathes, its stroke

can be reduced to 100 mm to allow

the bar feeder to be brought as close

as possible to the lathe; contact

IEMCA After-sales Service for more

information.

DANGER - WARNING: Perform bar

pusher extension manually. Please,

note that, without the front nose,

the bar feeder might be DANGEROUS

to the operator and/or installation

technician.

Max. bar pusher extension

Model Version Version

A –Max.

extension(mm)

BOSS 338 HD

BOSS 552 HD

21 - 32 – 37 – 44 - 64

910

L 1240

LL 1570

LL + 660

37 – 44 - 64

2230

Содержание BOSS 338 HD























































































































































































































Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды