IEMCA BOSS 338 HD Скачать руководство пользователя страница 58

Страница: 58 / 214

3 - SAFETY - GENERAL INFORMATION

Boss 338HD - 552HD

3 - Pag. 12 / 12

1)The colour loses intensity.

2)Other pieces of equipment or panels placed too close to the warning lamps on the bar feeder.

THERE ARE CIRCUITS NOT INTERRUPTED BY THE DISCONNECTING DEVICE

- There is danger caused by voltages from the lathe signals that are not interrupted by

disconnectors in the bar feeder.

During installation, check if it is possible to disconnect the system upstream from the bar feeder

using protection devices.

SEQUENCE OF PHASES

- It is very important that the operator knows the sequence of the bar feeder work phases.

These can be found in the Instruction Manual supplied with the machine.

DIFFERENTIAL CURRENT DEVICE UPSTREAM FROM THE MACHINE, USED TO PREVENT
HAZARDOUS CONDITIONS IN CASE OF A FAILURE

- Make sure that the bar feeder is powered by a three-phase power supply protected

through a differential switch with interrupting power (for example, of 30 mA).

RULES FOR ELECTRIC POWER SUPPLY

- Before performing the electrical connection of the bar feeder, check that the three-phase

power supply voltage that reaches it matches what is indicated on the identification plate
located on the electrical control panel door.

BAR PUSHER FEEDING AT START-UP

If the bar feeder is powered on (main switch to position I - ON) under the following conditions:

- Bar feeder guards are closed (feeding preliminary arrangements);

- Automatic and open collet signal (feeding enabled) from the lathe;

- Open/closed door signal (feeding enabled) from the lathe.

There is a risk of unwanted feeding of the bar pusher that moves until it meets a mechanical
obstacle .

To stop the bar pusher feeding:

1) Press the emergency button,

2) Switch off the feeding signal from the lathe,

3) Switch to manual mode from the lathe

Содержание BOSS 338 HD























































































































































































































Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание BOSS 338 HD

Отзывы:

Похожие инструкции для BOSS 338 HD

Бренды по названию

Популярные бренды