manualshive.com logo in svg

IEMCA BOSS 338 HD, Руководство по эксплуатации и техническому обслуживанию, Страница: 18 / 214

Поделиться
Скачать
IEMCA BOSS 338 HD Скачать руководство пользователя страница 18

 

EN 

2   -   TECHNICAL INFORMATION 

Boss 338HD - 552HD

 

 
 

2 - Pag. 2 / 2 

 

2.1 

BAR FEEDER GENERAL DESCRIPTION 

The BOSS automatic bar feeder is used in the machine-tool industry and in particular, for 
automatic lathe feeding. It is particularly suitable for feeding fixed or sliding headstock lathes, 
numerical control or cam lathes. 
The operating cycle is controlled by a PLC, integrated in the electrical control panel, which is 
able to communicate with the lathe control system. 
The digital handheld keyboard makes programming easier and allows the bar feeder functions 
to be controlled without leaving the lathe. 
The bar feeder can be used to feed bars, pipes, various sections and metallic as well as 
polymeric materials. Do not use flammable materials. 
The guide channel is completely closed during machining; a pump is provided to maintain a 
continuous oil flow inside the guide channel, creating a hydrodynamic support effect; these 
features allow the bar to rotate at high r.p.m., with no vibrations and no surface damaging. 
Thanks to the use of a "BRUSHLESS" and electronically controlled motor, the bar speed, torque 
value and bar feeding position may be determined at any time during the working cycle. 
 
The bar pusher returns with the remnant, which is removed and then falls into the remnant 
recovery box through a slot of the following size: L=400 mm, for Standard Remnant Drop (CSS) 
or L=700 mm for Oversize Remnant Drop (CSM). Please refer to the "VERSION DESCRIPTION" 
section in ch. 2 for technical specifications. 
The bar remnant ejection can be performed by the bar pusher feeding or next bar feeding. 
The BOSS bar feeders are available in the following models: 
BOSS 338 HD (standard version, magazine length: 21, 32, 37, 44, 64) 
BOSS 338r HD (reversed version, magazine length: 32, 37, 44) 
BOSS 552 HD (standard version, magazine length: 21, 32, 37, 44) 
BOSS 552r HD (reversed version, magazine length: 32, 37, 44) 
When not otherwise specified, the texts, tables and pictures of this manual refer to the 
standard version (BOSS 338 HD and BOSS 552 HD) with the lathe on the operator's right. 
 
 
As for the reversed version (BOSS 338r HD e BOSS 552r HD), with the lathe on the operator's 
left, please note that the main parts are located on the opposite side, as mentioned below. 
 
 

 

Содержание BOSS 338 HD























































































































































































































Отзывы:

Нет отзывов