IDT PowerSpan II Скачать руководство пользователя страница 198

Страница: 198 / 440

11. Signals and Pinout

198

PowerSpan II User Manual

80A1010_MA001_09

Integrated Device Technology

www.idt.com

PCI_REQ

[7:5]#

Input

PCI-1 Bus Request:

These inputs are used by external masters to request the

bus from the PCI-1 or PCI-2 arbiter. They are assigned to PCI-1 or PCI-2 by
software. These pins must be weakly pulled high in a system.

P1_REQ64#

Tristate bidirectional

PCI-1 Request 64-bit Transfer:

An active low indication from the current master

of its choice to perform 64-bit transactions. Rescinded by the bus master at the
end of the transaction.

P1_RST#

Tristate bidirectional

PCI-1 Reset:

Asynchronous active low reset for PCI-1 Interface

P1_SERR#

Open drain

PCI-1 System Error:

An active low indication of address parity error.

P1_STOP#

Tristate bidirectional

PCI-1 Stop:

An active low indication from the target of its desire to stop the

current transition. Sampled by the master. Rescinded by the target at the end of
the transaction.

P1_TRDY#

Tristate bidirectional

PCI-1 Target Ready:

An active low indication of the current target’s ability to

complete the dataphase. Driven by the target; sampled by the current bus
master. Rescinded by the target at the end of the transaction.

P1_64EN#

Input

PCI-1 64-bit Enable:

An active low indication that a CompactPCI Hot Swap

board is in a 64-bit slot. This signal must be pulled high in a non-Hot Swap
environment.

P1_RST_DIR

Input

(LVTTL)

PCI-1 Bus Reset Direction

P1_VDDA

Supply

PCI-1 Analog VDD:

Voltage supply pin to the analog circuits in the PCI-1 Phase

Locked Loop (nominally 2.5V).

P1_DVDD

Supply

PCI-1 Digital VDD:

Voltage supply pin to the digital circuits in the PCI-1 Phase

Locked Loop (nominally 2.5V).

P1_DVSS

Ground

PCI-1 Digital VSS:

Ground pin to the digital circuits in the PCI-1 Phase Locked

Loop.

P1_AVSS

Ground

PCI-1 Analog VSS:

Ground pin to the digital circuits in the PCI-1 Phase Locked

Loop.

Refer to the

PCI Local Bus Specification

for reset states and recommended terminations of these PCI signals.

To use the PowerSpan II Dual PCI in a 32-bit environment, add a pull-up resistor to P1_AD[32:63].

Table 56: PCI-1 Signals

Pin Name

Pin Type

Description

Содержание PowerSpan II

























































































































































































































































































































































































































































Результаты поиска

Содержание PowerSpan II

Отзывы:

Похожие инструкции для PowerSpan II

Бренды по названию

Популярные бренды

IDT PowerSpan II, Руководство пользователя

Результаты поиска

Содержание PowerSpan II

Отзывы:

Похожие инструкции для PowerSpan II

Бренды по названию

Популярные бренды