IDEC FS1A-C11S Скачать руководство пользователя страница 47

Страница: 47 / 398

BASIC OPERATIONS

4-9

r 4

Warning

Turn OFF the power to SafetyOne before inspection and/or connecting of the wires.

Canceling the Stop state

If the SafetyOne detects any wiring errors, abnormalities or internal circuit failure, it changes to

the Stop state and locks out operations. The Stop state can be cancelled by the following

method.



Cancellation by removal of power to SafetyOne

The Stop state is cancelled by restarting power to SafetyOne after removing the error.

Refer "Chapter 6 TROUBLESHOOTING" for information to identify the cause that generated

the Protection state or Stop state.

Содержание FS1A-C11S














































































































































































































































































































































































































Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды

IDEC FS1A-C11S, Руководство пользователя

Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды