IDEC FS1A-C11S Скачать руководство пользователя страница 298

Страница: 298 / 398

LOGIC

5-250

●External device monitor inputs: X12 to X15 (T12 to T15)

External device monitor inputs are used to diagnose status of the devices connected to safety outputs.

Intended inputs

(Terminal names)

Target safety

outputs (Terminal

names)

Function

External device monitor input 1

(X12-T12)

Safety output 1

(Y0)

Function name

External device monitor input

External device monitor input 2

(X13-T13)

Safety output 2

(Y1)

Symbol

External Device

Monitor

EDM

External device monitor input 3

(X14-T14)

Safety output 3-1

(Y2)

Description of

operation

This function diagnoses the

status of devices connected to a

target safety output.

External device monitor input 4

(X15-T15)

Safety output 3-2

(Y3)

Detail

information

Logic functions (5-326)

Warning

Safety check signals (pulses signals) are sent from the drive terminals (T12 to T15) to diagnose

external devices and monitor circuits. Safety check signals can not be used as a power supply for

connected devices.

Note. If there are unused safety outputs, connect the intended external device monitor terminals (Xn)

to the corresponding drive terminals (Tn). If they are not connected, the SafetyOne detects an
input monitor error. As the result, the error LED displays a “1” and the unit changes to the
Protection state.

Содержание FS1A-C11S














































































































































































































































































































































































































Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды

IDEC FS1A-C11S, Руководство пользователя

Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды