IDEC FS1A-C11S Скачать руководство пользователя страница 33

Страница: 33 / 398

INSTALLATION AND WIRING

3-3

r 3

Installation method

■ Installation location and direction

When the SafetyOne is installed in an enclosure, confirm that installation environments meet

the product specifications. Using in environments as a described below, (over the product

specifications) may cause fire hazard, damage, or malfunction.

- SafetyOne should not be exposed to excessive dust, dirt, salt, vibration or shocks.

- Do not use SafetyOne in an area where corrosive chemicals or flammable gases are present.

- Do not use SafetyOne near induction heat sources.

Mount SafetyOne with enough space from any device as shown at Fig3.1 for maintenance and

ventilation. Do not install SafetyOne near, and especially above, any heating device or heat

source.

Use SafetyOne in surrounding air temperature, -10 to +55 ºC.

Note1. Consider opening and closing of protective cover. (Min. 20mm)

Note2. Consider instllation to DIN rail and ventilation characteristic. (Approx. 20mm)

Note3. Consider distance to other devices can be heat source, such as safety relays.

(Approx. 40mm)

Note4. Consider wiring the cables connected to input/output connectors. (Approx. 80mm)

Min. 20mm

note1)

note3)

note2)

note4)

Panel

Fig. 3.1 Installation location

Содержание FS1A-C11S














































































































































































































































































































































































































Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды

IDEC FS1A-C11S, Руководство пользователя

Результаты поиска

Содержание FS1A-C11S

Отзывы:

Бренды по названию

Популярные бренды