ICP DAS USA tM-TH8 Скачать руководство пользователя страница 52

Страница: 52 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

2.10 $AA7CiRrr

Description:

Sets the type code of a channel.

Syntax:

$AA7CiRrr[CHKSUM](CR)

Delimiter character

Address of the module to be set (00 to FF)

Command to set the channel range code

i specifies the input channel to be set (0-7)

Rrr

rr represents the type code of the channel to be
set. Refer to the Temperature Sensor Type
Setting table in Section 1.10.

Response:

Valid command:

!AA [CHKSUM](CR)

Invalid command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command or
invalid type code

Address of the responding module (00 to FF)

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

tM-TH8

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды