ICP DAS USA tM-TH8 Скачать руководство пользователя страница 62

Страница: 62 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

tM-TH8

2.16 $AAP

Description:

Reads the communication protocol information.

Syntax:

$AAP[CHKSUM](CR)
$

Delimiter character

Address of the module to be read (00 to FF)

Command to read the communication protocol

Response:

Valid Response:

!AASC[CHKSUM](CR)

Invalid Response: ?AA[CHKSUM](CR)
!

Delimiter character for a valid response

Delimiter character for an invalid response

Address of the responding module (00 to FF)

The protocols supported by the module

0: only DCON protocol is supported
3: The DCON, Modbus RTU and Modbus

ASCII protocols are supported

Current protocol saved in EEPROM that will be
used at the next power on reset

0: the protocol set in EEPROM is DCON

1: the protocol set in EEPROM is Modbus RTU

3: the protocol set in EEPROM is Modbus
ASCII

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды