ICP DAS USA tM-TH8 Скачать руководство пользователя страница 93

Страница: 93 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

2.31 @AAGxTtt

Description:

Reads the Steinhart coefficient of a user-defined type.

Syntax:

@AAGxTtt[CHKSUM](CR)

Delimiter character

Address of the module to be read (00 to FF)

Command to read the Steinhart coefficient

A: reads Steinhart coefficient A
B: reads Steinhart coefficient B
C: reads Steinhart coefficient C

Ttt

tt represents the type code of the user-defined
type to read the Steinhart coefficient.

Response:

Valid command:

!AA(Data)[CHKSUM](CR)

Invalid command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command or
invalid type code

Address of the responding module (00 to FF)

(Data)

Eight hexadecimal digits to represent the
Steinhart coefficient in IEEE-754 format. See
Section 1.11 for details.

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

tM-TH8

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Похожие инструкции для tM-TH8

Бренды по названию

Популярные бренды