ICP DAS USA tM-TH8 Скачать руководство пользователя страница 96

Страница: 96 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

Examples:

Command: @01RTT70R0104500

Response: !01-032.64

Reads the temperature associated with 104500 ohms
of type 70 of module 01, and the module returns a
value of –32.64 degree.

Command: @01RTT70R00801.2

Response: !01+072.62

Reads the temperature associated with 801.2 ohms of
type 70 of module 01, and the module returns a value
of 72.62 degree.

Related Commands:

Section 2.19 ~AAD, Section 2.20 ~AADT, Section 2.31
@AAGxTtt, Section 2.33 @AASxTttC(data)

Related Topics:

Section A.6 Thermistor

Notes:

The temperature scale is set using the ~AADT command
and can be read using the ~AAD command. See Sections
2.19 and 2.20 for details.

tM-TH8

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды