ICP DAS USA tM-TH8 Скачать руководство пользователя страница 97

Страница: 97 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

2.33 @AASxTttC(data)

Description:

Sets the Steinhart coefficient of a user-defined type.

Syntax:

@AASxTttC(data)[CHKSUM](CR)

Delimiter character

Address of the module to be set (00 to FF)

Command to set the Steinhart coefficient

A: sets Steinhart coefficient A
B: sets Steinhart coefficient B
C: sets Steinhart coefficient C

Ttt

tt represents the type code of the user-defined
type to set the Steinhart coefficient.

C(Data) The (Data) is eight hexadecimal digits in IEEE-

754 format to represent the Steinhart coefficient.
See Section 1.11 for details.

Response:

Valid command:

!AA[CHKSUM](CR)

Invalid command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command or
invalid type code

Address of the responding module (00 to FF)

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

tM-TH8

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды