IBM RS/6000 SP Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 89

MAP 0160: Thin Processor Node Power

MAP 0160: Thin Processor Node Power

Note: Refer to "Service Position Procedures" in

IBM RS/6000 SP: Maintenance Information, Volume 3,

Locations and Service Procedures for placing or removing processor node(s) in/from service posi-
tion.

001

– From the system monitor, check the Power (green) LED for this processor node.
The definition of the Power (green) LED is as follows:

Power (Green)

Off

No 48 V dc power available at processor node.

Flashing Power available at processor node, but RS/6000 logic is Off.

On

Power available at processor node, and RS/6000 logic is On.

Is Power (green) LED Off?
Yes No

002

Processor node getting 48 V dc power.
Is Power (green) LED flashing?
Yes No

003

Power (green) LED is On, indicating no problem with power supply.
– Verify that you have the proper processor node, then go to “MAP 0130: Processor Node”

on page 1-30.

– If this is the proper processor node, call the next level of support.

004

Processor node is getting power.
– Power on RS/6000 logic from the virtual front panel on the control workstation.
Does Power (green) LED light and stay lit?
Yes No

005

Node not responding to the command.
– Go to “MAP 0110: Supervisor Subsystem” on page 1-10.

006

RS/6000 logic getting power.
Does processor node IPL successfully?
Yes No

007

Processor node has problem with IPL.
– Go to “MAP 0130: Processor Node” on page 1-30.

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-69

«
...
87
88
89
90
91
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды