IBM RS/6000 SP Скачать руководство пользователя страница 338

Страница: 338 / 388

MAP 0530: Switch Assembly Power

034 (continued)
Problem not resolved.
– Go to Step 035.

035

Problem with the 48 V dc power distribution to this switch assembly.
– Go to “MAP 0480: Open in 48 V dc Distribution” on page 1-283.

036

This is an SPS or SPS-8 assembly.
– Turn off the circuit breaker. Unplug cables connected to J1 and J2 at rear of the switch assembly. Then

remove the front panel assembly from the inner chassis.

– Unplug inner chassis cable from the switch power card(s) S00-PC-P4, S00-PC-P6 and the switch super-

visor card S00-SP-P5.

– Using a digital multimeter, check for inner chassis cable continuity from the switch tailgate and the con-

nectors in the following table:

– On the fan assembly, with CB in the On (‘1’) position, check for front chassis cable continuity between

the connectors in the following table:

Is there continuity?
Yes No

037

Continuity check failed on a cable.
Did the front chassis cable fail the continuity check?
Yes No

038

Inner chassis cable failed test.
– Replace inner chassis cable. Refer to "Removing the Switch Inner Chassis Cable (SPS,

SPS-8)" in

IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service

Procedures.

(Step 038 continues)

Table

1-9. Inner Chassis Cable Continuity

From

S00-BH_J1 pin 5&9

P6 pin 2

S00-BH-J1 pin 5&9

P4 pin 2

S00-BH-J1 pin 1&6

P3 pin 16

P3 pin 17

p6 pin 1

P3 pin 17

p4 pin 1

Table

1-10. Front Chassis Cable Continuity

From

P1 pin 17

P1 pin 16

1-318

RS/6000 SP MAPs

Содержание RS/6000 SP





































































































































































































































































































































































































Результаты поиска

Содержание RS/6000 SP

Отзывы:

Бренды по названию

Популярные бренды

IBM RS/6000 SP, Информация по обслуживанию

Результаты поиска

Содержание RS/6000 SP

Отзывы:

Бренды по названию

Популярные бренды