IBM RS/6000 SP Скачать руководство пользователя страница 259 | Manualshive

Страница: 259 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 259

MAP 0400: Supervisor Power 12 Volts DC Problem

DANGER

High voltage present. Perform “Lockout/Tagout Procedure for PDU” on page 1-2
or “Lockout/Bagout Procedure for PDU” on page 1-3 to remove primary power
to the frame.

– Open Power Distribution Unit dc section.
– Replace connector card.
– Go to Step 044 on page 1-242 to verify fix.

012

Power problem resolved.
– Go to “MAP 0570: End of Call” on page 1-357.

013

– Go to Step 014

014

Short in 12 V dc distribution.
– Disconnect supervisor harnesses PDU-BH-P7 and PDU-BH-P8 from the Power Distribution Unit.
– Check for short between connector card PDU-FC-J402 pin 1 and pin 2.
Does short disappear with both cables removed?
Yes No

015

– Disconnect supervisor tailgate cables at connector card PDU-FC-J406 and PDU-FC-J408, then

check for short between connector card PDU-FC-J402 pin 1 and pin 2.

Does short disappear with both cables removed?
Yes No

016

Short in frame supervisor card cage.
– Unscrew connector card faceplate and unseat connector card from backplane card.
– Check for short between connector card PDU-FC-J402 pin 1 and pin 2.
Has short disappeared?
Yes No

017

– Replace connector card.
– Go to Step 043 on page 1-242.

018

– Reseat connector card.
– Unscrew frame supervisor card faceplate and unseat frame supervisor card from backplane

card.

– Check for short between connector card PDU-FC-J402 pin 1 and pin 2.
(Step 018 continues)

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-239

«
...
257
258
259
260
261
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов