manualshive.com logo in svg

IBM RS/6000 SP, Информация по обслуживанию, Страница: 328 / 388

Поделиться
Скачать
IBM RS/6000 SP Скачать руководство пользователя страница 328

 

MAP 0520: Switch Assembly Environment

 

 

 

030 (continued)
– If necessary, reconnect all cables at the rear of the switch assembly.
– Put circuit breaker at the front of the switch assembly in the On (‘1’) position.
– Go to Step 101 on page 1-350.

031

– One or more of the following conditions exist:

 

Ÿ

“...P33Low...”

 

Ÿ

“...P33High...”

 

Ÿ

“...Pvolt33Range...”

 

Ÿ

“...PS1Fail...”

 

Ÿ

“...PS2Fail...”

 

Ÿ

“...PSFuseGood...”

– Have the customer remove the switch assembly from the active configuration and power off the switch

assembly.

– Switch off the circuit breaker. Unplug cables connected to J1 and J2 at rear of the switch assembly.

Then remove the front panel assembly from the inner chassis.

– Put the switch into service position. Refer to "Service Position Procedures" in 

IBM RS/6000 SP: Mainte-

nance Information, Volume 3, Locations and Service Procedures.

Does condition state a P33 type problem?
Yes  No

032

Condition is PSxFail or PSxFuseGood.
– Go to Step 042 on page 1-309.

033

Condition is P33Low, P33High, or voltP33Range.
– Check cable conditions at switch supervisor card S00-SC-P5 and switch power card(s) S00-PC-P4 and

S00-PC-P6.

Does the inner chassis cable appear to be okay?
Yes  No

034

Problem with inner chassis cable.
– Go to Step 019 on page 1-304, Priority 4, to replace cable.

035

Condition is P33 type.
Does condition state P33low or voltP33Range?
Yes  No

036

Condition is P33High.
– Go to Step 053 on page 1-311

037

(Step 037 continues)

1-308

RS/6000 SP MAPs 

 

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов