IBM RS/6000 SP Скачать руководство пользователя страница 280 | Manualshive

Страница: 280 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 280

MAP 0440: Short in 48 Volts DC Power Distribution

013 (continued)
Is there an obvious problem with the 48 V dc power harness?
Yes No

014

– Replace the 48 V dc power harness.
– Reconnect the processor node or switch assembly and check for a short condition

again.

– Continue at the second bullet (powering on any bulk dc power supplies that are Off)

of Step 012 on page 1-259.

015

– Correct the obvious problem. If necessary, replace the 48 V dc power harness.
– Reconnect the processor node or switch assembly and check for a short condition again.
– Continue back at the second bullet of Step 012 on page 1-259.

016

– Go to Step 009 on page 1-259 and reconnect next cable.

017

Possible short in processor node(s) or switch assemblies.
– Put processor node and switch assembly circuit breakers in On (‘1’) position one at a time, checking the

frame supervisor green LED #2 for an OFF condition, indicating a short condition.

Are you able to power on all processor nodes and switch assemblies without indication of a short
condition?
Yes No

018

– Remove the processor node or switch assembly causing the short condition from the frame.
– Check the 48 V dc power harness inside the processor node or switch assembly for an obvious

problem which might be causing the short condition.

Is there an obvious problem which might be causing the short condition?
Yes No

019

– Replace the node supervisor card or switch power card.

Note: If this is an HiPS 2.0 switch assembly, replace the entire switch assembly to fix

problem.

– Reconnect the processor node or switch assembly and put circuit breaker in the On (‘1’)

position.

– From the control workstation, enable any power supplies that are turned off.
– Go to Step 017.

020

– Fix the obvious problem which might be causing the short condition.
– Reconnect the processor node or switch assembly and put circuit breaker in the On (‘1’) position.
(Step 020 continues)

1-260

RS/6000 SP MAPs

«
...
278
279
280
281
282
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды