IBM RS/6000 SP Скачать руководство пользователя страница 363 | Manualshive

Страница: 363 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 363

MAP 0540: Switch Function

055 (continued)
Are there still problems reported on all data cables connected to this switch assembly?
Yes No

056

Clock problem resolved for this switch assembly.
– Go to Step 100 on page 1-350

057

Problem with switch planar.
– Go to Step 094 on page 1-349 to replace switch assembly.

058

– Go to Step 060.

059

– Go to Step 065 on page 1-344.

060

Probable problem with original external clock source.
– Based on the original external clock selection, locate the frame which was sourcing the switch clock.

Locate a “test” processor node in this frame which can be used for service.

– Disconnect the switch data cable for this processor node at the tailgate of the switch assembly.
– Using switch cabling list, locate the switch data cable (S00-BH-J3, S00-BH-J5, S00-BH-J7, or

S00-BH-J9) at the processor node frame that sources the clock to the failing switch assembly. Discon-
nect this cable at the tailgate of the processor node frame, then connect the end of the processor node
data cable to the jack.

– Run advanced diagnostics on “css0” on the “test” processor node. Do not perform cable wrap test. Ref-

erence "Running Diagnostics in a Processor Node" in

IBM RS/6000 SP: Maintenance Information,

Volume 3, Locations and Service Procedures, as required.

– Look for an SRN indicating a clock problem (such as “External clock”) is one of the failing components.
Do the “css0” diagnostics fail with an indication of a clock problem?
Yes No

061

Problem is either cable or reported switch assembly.
– Replace switch data cable that originally supplied the switch clock to the failing switch assembly.
– Set the switch clock selection on this switch assembly to the original (correct) setting.
– From the control workstation of the primary node, enter:

Estart

to reinitialize the switch.

– Check the /var/adm/SPlogs/css/out.top file to see if problems are still reported on all data

cables connected to this switch assembly.

(Step 061 continues)

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-343

«
...
361
362
363
364
365
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов