IBM RS/6000 SP Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 225

MAP 0340: POWER3 SMP Thin and Wide Node Power

047 (continued)
Was a shorted condition detected?
Yes No

048

– Replace the power/supervisor cable assembly in the logic part of the node.
– Remove processor node from service position.
– Reconnect all cables at rear of processor node.
– Go to Step 041 on page 1-204.

049

– Replace corresponding power supply.
– Remove processor node from service position.
– Reconnect all cables at rear of processor node.
– Go to Step 041 on page 1-204.

050

– From control workstation or processor node, check node supervisor green LED 1 for this node.
Is node supervisor green LED 1 off or is ‘No Power to Node’ displayed on the control workstation?
Yes No

051

Processor node problem resolved.
– Go to “MAP 0570: End of Call” on page 1-357.

052

– Check processor node(s) on any other dc power harness for any that are powered on. Ensure that the

other processor node has its circuit breaker in the On (‘1’) position.

– Check the green LED 1 for an On or Flashing condition.
– POWER3 SMP processor nodes receive 48-volt power by connecting a power cable between the node

and the SEPBU bulkhead.

PDU-BH-P1:

Processor nodes

1, 2, 3, 4

PDU-BH-P2:

Processor nodes

5, 6, 7, 8

PDU-BH-P3:

Processor nodes

9, 1ð, 11, 12

PDU-BH-P4:

Processor nodes 13, 14, 15, 16

PDU-BH-P21: first SMP Node 1
PDU-BH-P22:

Second SMP Node

5

PDU-BH-P23: Third SMP Node 9
PDU-BH-P24:

Fourth SMP Node 13

Is the green LED 1 on any other processor node On or Flashing?
Yes No

053

– Go to “MAP 0370: Main Power” on page 1-222.

054

– Check all other processor nodes on the same dc power harness as the failing processor node to check

for the same symptom - circuit breaker on but green LED 1 not lit.

(Step 054 continues)

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-205

«
...
223
224
225
226
227
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды