IBM RS/6000 SP страница 365 Скачать руководство пользователя | Manualshive

Страница: 365 / 388

background image

MAP 0540: Switch Function

069 (continued)
This is an HiPS 3.0 assembly.
– The switch clock selected for this frame is from one of the following sources (with corresponding switch

data cables):

Internal

:

No cable

External 1 :

Sðð-BH-J3

External 2 :

Sðð-BH-J5

External 3 :

Sðð-BH-J7

– Go to Step 070

070

– Disconnect clock source data cable at S00-BH-J3, J5, J7, or J9, then reconnect to switch assembly.

(This is done to eliminate clocking noise from cable.)

– Find a processor node in the “problem” frame which is usable for service. This will be used as the “test”

processor node.

– Run advanced diagnostics on “css0” on the “test” processor node. Do not perform cable wrap test. Ref-

erence "Running Diagnostics in a Processor Node" in

IBM RS/6000 SP: Maintenance Information,

Volume 3, Locations and Service Procedures, as required.

– Look for an SRN indicating a clock problem, i.e. “External clock” is one of the failing components.

Note: Do not exit from diagnostics at this time, as it may be used in the following steps.

Do the “css0” diagnostics fail with indication of a clock problem?
Yes No

071

Diagnostics did not fail with indication of a clock problem.
Is this the first time at this step?
Yes No

072

– Go to Step 101 on page 1-350 to verify the fix.

073

– Disconnect the switch data cable corresponding to the selected clock at the switch assembly.
– Run advanced diagnostics on “css0” on the “test” processor node. Do not perform cable wrap

test. Reference "Running Diagnostics in a Processor Node" in

IBM RS/6000 SP: Maintenance

Information, Volume 3, Locations and Service Procedures, as required.

– Look for an SRN indicating a clock problem, i.e., “External clock” is one of the failing components.

Note: Do not exit from diagnostics at this time, as it will be used in the following steps.

Do the “css0” diagnostics fail with indication of a clock problem?
Yes No

074

Problem is the clock selection in this switch assembly.
– Replace the clock card in this switch assembly. Make sure to connect all cables connected

to the clock card.

– Reinstall only the two switch data cables which are not selected and the switch data cable

to the “test” processor node. Do not connect the remaining switch data cables at this time.

(Step 074 continues)

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-345

«
...
363
364
365
366
367
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RS/6000 SP

Бренд: Lantronix Страницы: 6

Бренд: Lantronix Страницы: 27

Бренд: Velleman Страницы: 17

AirLive WP-203G

Бренд: Ovislink Страницы: 132

Transport TX46 (B4985) Service

Бренд: TYAN Страницы: 75

Бренд: IBM Страницы: 82

Бренд: Avaya Страницы: 84

Бренд: Ekselans Страницы: 37

Бренд: Axis Страницы: 85

Бренд: Cisco Страницы: 40

Бренд: 7th Sense Страницы: 156

6180DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

ProLiant Moonshot

Бренд: HP Страницы: 21

Бренд: ASUSTOR Страницы: 12

TalkAnytime TA2410

Бренд: Multitech Страницы: 235

Бренд: innuos Страницы: 9

Бренд: innuos Страницы: 13

Бренд: Inspur Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды