IBM RS/6000 SP Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 208

MAP 0320: 332 MHz SMP Node Minimum Configuration

012 (continued)
Remove CPU card 2 (slots J5/J6), if installed.
Remove all DASD except for the boot DASD (hdisk0).

– Set the circuit breaker to the On (‘|’) position.
– Reseat the node supervisor by unplugging, then plugging, the supervisor cable at the rear of the node.
Does the node IPL properly?
Yes No

013

Replace the following components, one at a time, and IPL the node.

Memory DIMM
Memory card
CPU card
Service processor card
Boot DASD
DASD cable (2-drop or 4-drop)
I/O planar
System planar
Flat ribbon power cable

Does the node IPL properly?
Yes No

014

– Replace next component in list on Step 013.
– If all components have been replaced, call next level of support.

015

Last component replaced was defective.
– Go to Step 016.

016

Add the components removed in Step 012 on page 1-187, one at a time, and IPL the node.
Does the node IPL properly?
Yes No

017

Component failed.
– Replace failing component and IPL the node.
Does the node IPL properly?
Yes No

018

Component failed.
– Replace failing component.
– Go to Step 017

019

(Step 019 continues)

1-188

RS/6000 SP MAPs

«
...
206
207
208
209
210
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов