IBM RS/6000 SP Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 388

IBM RS/6000 SP Скачать руководство пользователя страница 308

MAP 0500: Ethernet LAN

MAP 0500: Ethernet LAN

Each processor node has at least one Ethernet LAN connection:

Standard RS/6000 SP system (and coexistence 9076 SP1 system):

Thin processor nodes:

Integrated Ethernet connection (N00-BH-J5). Connects this processor
node to the customer’s LAN.

Important Note for Thin Nodes with TTP

The Ethernet riser card port on the thin node (and thin node 2) must
be set to the “thick” position. See “Setting the Ethernet Riser Card
Jumpers” in the Removal and Replacement section of

7012

POWERstation and POWERserver: Install and Service Guide
(SA23-2624) for details.

Wide processor nodes:

Micro Channel Ethernet connection (N00-MC-0/1). Connects this processor
node to the customer’s LAN.

604 or 604e high processor nodes:

Micro Channel Ethernet connection (N00-MC-1/1). Connects this processor
node to the customer’s LAN.

SP-Attached Server S70 and S7A

PCI Ethernet connection (ent0). connects this processor node to the cus-
tomer's LAN.

332 MHz SMP or POWER3 SMP nodes:

Integrated Ethernet connection (not riser card). Connects this processor
node to the customer’s LAN.

Additional Ethernet cards may be present in the I/O adapter slots.

Items covered in this MAP are for cabling with coax (BNC) connections or TTP connections:

Integrated Ethernet card

Micro Channel Ethernet card

PCI Ethernet card

Ethernet cabling inside the RS/6000 SP frame

Ethernet connections outside the RS/6000 SP frame.

Ethernet transceiver (TTP)

MAU (TTP)

001

The factory default wiring topology for coax is similar to the following:

Terminator

→

Customer's LAN

→ (Nð2 → Nð1) → (Nð3 → Nð4) → (Nð6 → Nð5) → (Nð7 → Nð8)
→ (N1ð → Nð9) → (N11 → N12) → (N14 → N13) → (N15 → N16)

→ Terminator

where:

N## refers to processor node number,
Processor node pairs are in '()'s.

The wiring topology for TTP is similar to the following figure:

1-288

RS/6000 SP MAPs

«
...
306
307
308
309
310
...
»

Содержание RS/6000 SP





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды