IBC CX Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 124

IBC CX Series Скачать руководство пользователя страница 83

6.3.5 Testing the Hi-Limit cutoff temperature function

The hi-limit temperature function monitors the maximum supply temperature set in the safety
ignition module (SIM). If the water temperature exceeds the hi-limit temperature, the boiler goes
into a lockout condition, requiring a manual reset. Perform the test to ensure that the water
temperature sensor is functioning.

To test the Hi-limit temperature function:

1. Go to

>

SIM Menu

>

Hi-Limit Test

> Read the instructions.

You will need to enter a cutoff temperature below the actual supply temperature value
currently displayed. For example, if the Supply Temp. value is 180°F, enter 170°F in the Cut
Off Temp. box.

2. In the

Cut-Off Temp.

field, enter a number value >

OK

.

The message: "Hi-Limit Detected" is displayed.

3. To reset the boiler, select the

Reset

button. The cutoff value reverts to normal upon reset.

The message: "The SIM module has been reset" is displayed.

4. Tap

Close

>

Back

to exit the test.

83

6.3.5 Testing the Hi-Limit cutoff temperature function

«
...
81
82
83
84
85
...
»

Содержание CX Series





























































































































Отзывы:

Нет отзывов