IBC CX Series Скачать руководство пользователя страница 107

Страница: 107 / 124

5. If the error persists, perform a LWCO test. Go to

SIM Menu

Hi-Limit Test

> Run

the test to check if the low water cutoff sensor is opening.

8.1.5.3 Resetting a boiler after a hi-limit temperature lockout

A boiler in a lockout condition due to a hi-limit temperature error will need to be reset.

1. Go to

Clear Errors

Yes

2. Check that there is no air trapped in the system and that the boiler is pressurized.

3. To reset the SIM Module, go to

SIM Menu

Hi-Limit Test

Reset

Yes

4. Run the boiler to ensure that the error has been cleared.

5. If the error persists, perform a hi-limit test. Go to

SIM Menu

Hi-Limit Test

> Run

the test to see if the hi-limit switch is operational. You can also perform this test for gasket
blowouts.

8.2 Troubleshooting error messages

Warning

Never attempt to repair the control module (circuit board). If the control module is
defective, replace it immediately.

Errors shown on the touchscreen controller are described below as well as diagnoses and fixes.

The bottom line of the touchscreen displays the boiler's error status. The following colors represent
the boiler's operating status:

Green – Normal

Yellow – Warning

Red – Alarm

The text inside the bar will indicate the specific warning or alarm. If there is more than one alarm
present the text will scroll slowly through all current alarm conditions. Besides the errors listed below,
see also

Miscellaneous touchscreen controller errors on page 109

107

8.2 Troubleshooting error messages

Содержание CX Series





























































































































Результаты поиска

Содержание CX Series

Отзывы:

IBC CX Series, Инструкция по установке и эксплуатации, Страница: 107 / 124

Результаты поиска

Содержание CX Series

Отзывы: