IBC CX Series Скачать руководство пользователя страница 110

Страница: 110 / 124

Miscellaneous errors

Issue

Diagnosis

Fix

"service" mode after
software update.

updates applied.

operation.

8.3.1 Ignition issues

Ignition issues

Issue

Diagnosis

Fix

Noisy spark
when
igniting

Ignition lead is not firmly
connected.

Reconnect ignition lead.

Contaminants/moisture
on igniter probe/flame
sensor.

Ensure probe is dry by re-running post-purge;
otherwise, clean or replace igniter probe.

Boiler
rumbles
when
igniting.

Fluctuating gas
pressure/ gas pressure
too high/too low.

Check CO

level via analyzer.

Check for proper gas
piping

Check pressure with manometer during ignition.

Boiler will
not attempt
to ignite.
Fan and
pump are
operating
normally.

No power to ignition
control module.

Check system wiring.

Check air reference tubing.

Igniter probe/flame
sensor disconnected.

Reconnect probe.

Defective Control
Module.

Check ignition output from control module.

Boiler will
not attempt
to ignite.
Fan and / or
pump are
off. Display
not
illuminated

No power to boiler.

Check line voltage.

Defective transformer.

Check transformer. Reconnect or replace as needed.

110

Section: Troubleshooting

Содержание CX Series





























































































































Результаты поиска

Содержание CX Series

Отзывы:

IBC CX Series, Инструкция по установке и эксплуатации, Страница: 110 / 124

Результаты поиска

Содержание CX Series

Отзывы: