IBC CX Series Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 124

IBC CX Series Скачать руководство пользователя страница 16

1.2 Warranty

For residential applications, IBC offers a 5-year warranty on all parts (including the DHW heat
exchanger), against defects in materials or workmanship and failures due to thermal shock only.

IBC offers a combustion heat exchanger (space heating)15-year limited warranty with
registration, according to the following terms:

0-10 years (100% coverage)

11-15 years (25% coverage).

IBC offers a limited combustion heat exchanger warranty with no registration of 0-5 years (100%
coverage).

For commercial applications, IBC offers a 5-year warranty on the combustion heat exchanger
(space heating) and a 2-year warranty on all parts (including the DHW heat exchanger), against
defects in materials or workmanship and failures due to thermal shock only.

To view the full warranty statement for the CX series, go to

.

16

Section: Introduction

«
...
14
15
16
17
18
...
»

Содержание CX Series





























































































































Отзывы:

Нет отзывов