IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 67

Страница: 67 / 208

2-5

Ins

tal

lat

ion

Storage/preservation environment

●

For the storage and preservation environment, see the installation environment.

However, give especial consideration to the prevention of condensation during
long-term storage/preservation.

●

Unless especially specified, desiccant is not included in the package at shipping.

If the product is to be stored/preserved in an environment where condensation is
anticipated, take condensation preventive measures.

●

For short

-term storage, it can be stored at 60°C or below.

For storage of one month or more, make sure that the temperature does not exceed

50°C.

●

The product should be placed horizontally for storage and preservation.

If storing in the packaged condition, observe the conditions, if any, regarding storage
orientation.

2.2 Installation and storage/preservation environment

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 67 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: