IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 155

Страница: 155 / 208

7-6

roubl

hoot
ing

7.3 Troubleshooting with no alarm generated

Operation failure

[Condition 1] SV/ALM LEDs do not light up

No.

Possible cause

Confirmation/countermeasure

The specified power is not supplied.

●

Make sure that normal voltage is secured

and wiring processing is correct.

●

Also, be sure to check for disconnection

or partial disconnection in connectors
and wiring.

→

For details, refer to "3.4/3.5 Wiring

connections".

The unit is switched to servo OFF
with the teaching tool.

Turn ON the servo with PC software or
teaching pendant.

Controller breakdown

●Replace the

controller cover assembly.

→ For details, refer to "

Controller

replacement

(page 8-15)".

●If the unit still does not recover,

contact IAI.

[Condition 2] SV/ALM LEDs light up red

No.

Possible cause

Confirmation/countermeasure

Alarm generated.

●Connect

the teaching tool.

●Upon checking the alarm code,

resolve the cause.

→ For details, refer to "7.4 Troubleshooting

by alarm groups".

The stop switch of the
teaching pendant is being pressed.

Release the stop switch.

7.3 Troubleshooting with no alarm generated

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 155 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: