IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 178

Страница: 178 / 208

8-11

8. Maintenan

ce and Inspection

[TC/TW table guide]

(1) With the power off, pull out the table.

If the rod bracket will not move at low lead, connect to the PC software or teaching

pendant to move the table.

(2) From the grease lubrication port, apply the designated grease (TC: 0.2 to 0.4cc,

TW: 0.1 to 0.3cc) with a syringe, etc.

TW4 has different grease ports on the right and left guide; apply grease to both.

(3) Move the table to apply the grease thoroughly.

[TC] [TW]

[Table guide grease port cross-section figure]

Move the table to the stroke end to match the table grease port with the table guide

grease port.

Insert the syringe from the table grease port and apply grease to the table guide grease

port.

Be careful not to let the grease leak to the exterior.

* To release the brake, refer to

Brake

release method

(page 3-3)

8.5 Greasing method

Grease port (left/right collective)

Grease port (right)

Grease port (left)

Syringe, etc.

Table

Table guide

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 178 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: