IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 114

Страница: 114 / 208

4-9

perat

ion

Pressing operation setting

Setting item

Unit

Explanation

Pressing

starting point

The position where pressing operation starts.
Enter as the distance from the home position.
Entries can be made in increments of 0.01mm.

Pressing

force

The current limit value during the pressing operation.
Set between 20 and 40%.
[Switch units] can be used to input values in N units.

The pressing speed is 20 mm/s.
If [V: Velocity] is set to 20mm/s or below,
pressing will take place at the speed of [V: Velocity].

Caution

The pressing force displayed in N units serves as a guideline.

→ Refer

to "Pressing force and current limit value relationship" on pages

1-6/9/13/18/23.

When the pressing speed is 20mm/s or less, the pressing force will become unstable,
and failure to operate normally is possible.

Check [Press].

The screen will switch to the pressing operation window.

Action

4.3 Setting/adjustment of operating conditions (AVD)

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 114 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: