IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 121

Страница: 121 / 208

4-16

4. Operation

4.5 Operating method from master device

Home return operation/positioning operation

: [ST0] [LS0] [ST1] [LS1] signals

Turning the [ST0] signal ON when home return is not complete will first trigger home return operation. After a

momentary stop at the home position, it will then move to the backward end. As well, when the [ST1] signal is

turned ON, the unit will move to the forward end after home return operation. However, for battery-less absolute

encoder specification, the positioning operation should be conducted without having the home return operation.

(1) When the [ST0] signal is turned ON, backward motion begins towards the mechanical end. The movement speed is

20mm/s.

(2) Once the mechanical end is struck, the direction will be reversed and forward motion will begin.

The unit will move forward until the home position, then stop.

(3) After that, it will continuously move forward until the backward end, where it stops as operation is complete.

Caution

In the home reverse specification (model: NM), home return operation is in the reverse
direction.

4.5 Operating method from master device

(1) Backward

(2) Forward

(3) Forward

Backward signal [ST0]

Backward end signal [LS0]

ELECYLINDER

movement

(1) Backward

(2)Forward

(3) Forward

Home

Backward end

Reverse at mechanical end

Turning the ST signal OFF midway
through operation will interrupt
home return operation.

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 121 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: