IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 130

Страница: 130 / 208

5-3

rev
ent
ive

redi
ctiv

enanc

P di ti

Overload warning level

Name

Symbol Unit

Input range

Default setting

at shipping

Overload warning

level

OLWL

50 to 100

100

(disabled setting)

●

With the motor temperature rise value which triggers an overload alarm as 100%,

set the level to output an overload warning between 50 and 99%.

●

When the motor temperature rise value during operation exceeds the ratio set as

"overload warning level", the user will be notified with "Maintenance warning 3".

●

When the motor temperature rise value falls below the ratio set as

"overload warning level", "Maintenance warning 3" will be automatically cleared.

●

When "Maintenance warning 3" is output, investigate the cause of the increase

in load. Maintenance such as greasing or reviewing the operating conditions is
recommended.

●

Setting it to "100%" will disable this function.

Temperature change

under abnormal

conditions

Temperature change under normal conditions

Time

⇒

Warning output without stopping operation

oto

r tem

per

atu

⇒

Stops operation

Overload alarm detection value
(100%)

Overload warning level set value
(50 to 99%)

5.2 Maintenance information

Load increase

Alarm output

Warning

output

Perform

maintenance

Breakdowns and malfunctions can
be prevented by performing
maintenance after a warning is
output.

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 130 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: