IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 156

Страница: 156 / 208

7-7

roubl

hoot
ing

[Condition 3] The unit does not operate even when a command

is sent from a master device such as a PLC

No.

Possible cause

Confirmation/countermeasure

I/O signal communication is not established

●

Check the input/output status of the I/O

  signal with the monitoring function of the
  teaching tool. (both the master device and
  the ELECYLINDER)

●

Make sure the I/O signal voltage is normal.

●

Check whether the length of the I/O signal

  cable is within 10m, and whether the wire
  diameter is thinner than the applicable
  value.

●

Make sure the wiring processing is correct.

→ For details, refer to "3.4/3.5 Wiring

connections".

Disconnection of power I/O cable,
disconnection or contact failure of power
I/O connector

●

Check whether the cable is

disconnected/partially disconnected.

●

Make sure that the connector and cable are

not pulled out.

→

For details, refer to "3.4/3.5 Wiring

connections".

Movement command issued to stopping
position

→ When stopping at "Forward end",

check the ladder sequence by
sending a "Forward" command etc.

Check the ladder sequence and the setting of
the forward end/backward end.

Edge signals are input to "Forward" and
"Backward".

Check the ladder sequence and input level
signals.

* For details on I/O signals, refer to "4.4 I/O signals".

7.3 Troubleshooting with no alarm generated

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 156 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: