IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 132

Страница: 132 / 208

5-5

rev
ent
ive

redi
ctiv

enanc

Basic operation

To set the target value,
touch the field of the relevant item.

The set value will blink and

Ten Key window will open.

Enter the value with the Ten Key pad
and touch the [ENT] key.

The target value will change.

If you touch [ESC],
the target value will not be changed and
the original window will return.

Touch the [Information Edit] button.

A confirmation message

for rebooting the controller will be displayed.

The setting change will take effect
after rebooting.

If the actuator has been replaced,
touch the "Actuator replacement" button.

"Total travel count" and
"Total travel distance" will be
cleared to "0".

Action

5.3 Setting maintenance information

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 132 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: