manualshive.com logo in svg

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 125 / 208

Поделиться
Скачать
IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 125

 

 

4-20 

4.

 O

perat

ion

 

 

The torque (current limit value) 

configured for [Pressing force] in the Simple Data Setting screen 

judges completion of pressing operation. 
 
When the ELECYLINDER is performing pressing operation, satisfying the following conditions will 
produce a judgment of pressing complete, turning ON the PE signal. 

 
(Accumulated time in which current has reached pressing value [%]) - 
(A

ccumulated time in which current is less than pressing value [%]) ≥ 255ms

 

 
 
 
 
 
 
 
 
 
 

 
 
 

 

 
 
 
 
 
 
 
 
Points of caution for when the workpiece is not struck (no contact) and the movement to forward 
end or backward end is complete. 

Consider a master device sequence or detection method based 

on the content below. 

●

 If no contact is made, the PE signal will not turn ON. 

 

A timer is required to determine if no contact has been made.

 

●

 After a non-contact operation, the unit will stop in the pressing operation status. 

●

 If the workpiece shifts once pressing complete is determined and the PE signal is ON,   

  the ELECYLINDER will start another approach operation with the PE signal still ON. If the   
  workpiece cannot be pressed again, it will remain ON even with no contact. 

 

 

Reference 

4.5 Operating method from master device 

Reference 

Current 

 

Time 

 

Pressing [%] 

 

Operation 

start 

 

Approach operation end 

Pressing start 

 

200ms 

 

20ms 

 

75ms 

 

295ms 

 

200ms + 75ms - 

20ms ≥ 255ms

 

Pressing complete (PE output) 

 

Contacting 

workpiece 

 

   

 

 

Decrease in current due to 

movement of workpiece

 

Содержание EC ELECYLINDER EC-GD4

















































































































































































































Отзывы:

Нет отзывов