IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 208

IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 50

1-21

1. S

pecifications

[Payload by Speed/Acceleration]

At low load capacity, the acceleration/deceleration can be increased.
The maximum acceleration/deceleration is 0.5G for lead 4 and lead 6 and 0.3G for lead 2.
For % input, 0.5G for lead 4 and lead 6 and 0.3G for lead 2 are set as 100%.

Caution

Do not attempt to configure settings for acceleration/deceleration above the allowable
values.
This may lead to vibration, breakdown, or shortened product life.

Lead 6

Lead 4

Orientation

Horizontal

Vertical

Orientation

Horizontal

Vertical

Speed

(mm/s)

Acceleration (G)

Speed

(mm/s)

Acceleration (G)

0.3

0.5

0.3

0.5

0.3

0.5

0.3

0.5

0

2.5

2.5

1

1

0

4

4

1.5

1.5

300

2.5

2.5

1

1

200

4

4

1.5

1.5

Lead 2

Orientation

Horizontal

Vertical

Speed

(mm/s)

Acceleration (G)

0.3

0.3

0

8

2.5

100

8

2.5

1.2 Mechanical specifications

«
...
48
49
50
51
52
...
»

Содержание EC ELECYLINDER EC-GD4

















































































































































































































Отзывы:

Нет отзывов