IAI EC ELECYLINDER EC-GD4 Скачать руководство пользователя страница 158

Страница: 158 / 208

7-9

roubl

hoot
ing

[Situation 3] Shock or vibration is observed in acceleration/deceleration

No.

Possible cause

Confirmation/countermeasure

●

Acceleration/deceleration setting is

too high.

●

A load susceptible to acceleration

and deceleration is mounted.

●

The ELECYLINDER is mounted on

equipment with a structure
susceptible to acceleration and
deceleration.

●

Lower the acceleration/deceleration

setting.

●

Enable Parameter No. 5 "Smooth

accel/decel setting" and check its effect.

→ For details, refer to "6.4 Parameter

function descriptions".

Load inertia is excessive.

Lower the deceleration and suppress
overshoot.

[Situation 4] The unit vibrates slightly while stopped

No.

Possible cause

Confirmation/countermeasure

●A load susceptible to vibration is

mounted.

●The ELECYLINDER is mounted on a

frame with a structure susceptible to
vibration.

●Lower the acceleration/deceleration

setting.

●If Parameter No. 6 "Current control

setting at stop" is disabled, enable it and

check its effect.

→ For details, refer to "6.4 Parameter

function descriptions".

7.3 Troubleshooting with no alarm generated

Содержание EC ELECYLINDER EC-GD4
















































































































































































































Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы:

IAI EC ELECYLINDER EC-GD4, Инструкция по эксплуатации, Страница: 158 / 208

Результаты поиска

Содержание EC ELECYLINDER EC-GD4

Отзывы: