i3 International Veo16i Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 96

i3 International Veo16i Скачать руководство пользователя страница 66

System Setup > Storage Settings

Revision: 180906

Veo16i User Manual

Page | 65

Use this setup when using one single joystick/control device or one remote controller to control several
Veo16i DVRs.

>

SYSTEM ID: Set the DVR ID so the joystick/control device can distinguish between different
Veo16i units.

>

PROTOCOL: Select joystick/control device protocol from the list of available protocols. Refer to
your joystick/control device manual for more information.

>

BAUD RATE: Set joystick/control device baud rate. Refer to your joystick/control device manual
for more information.

>

REMOTE CONTROLLER ID: Set the remote controller ID. Default value is set to 0.

Click

APPLY

to save new configurations.

When done, click

CLOSE

or press [

EXIT

] on the remote control.

Storage Settings

<SYSTEM SETUP> - <STORAGE>

View the storage information of your Veo16i DVR, set the disk overwrite mode, format your storage hard
drives, configure RAID1/RAID5 array and set S.M.A.R.T. check interval.
Use mouse cursor or the navigation buttons on the remote control (

▲▼

◀▶

/ ENTER)

Disk Information

<SYSTEM SETUP> - <STORAGE> - <DISK INFORMATION>

Use mouse cursor or the navigation buttons on the remote control (

▲▼

◀▶

/ ENTER) to switch between

INTERNAL DISKS

and

EXTERNAL STORAGE

tabs.

>

START / END TIME: Show start and end time of the video data stored on each disk.

>

STATUS: Shows the current disk status. If the HDD is healthy and is being used for video
recording, the status will say

IN USE

. If the drive has malfunctioned, Veo16i will stop recording

to it and the status will show

NOT IN USE

.

Make sure to investigate the cause of all “NOT IN USE” status messages and promptly replace
failed hard drives to prevent video recording interruptions.

«
...
64
65
66
67
68
...
»

Содержание Veo16i

































































































Отзывы:

Нет отзывов